Skincare finishing agent "Mild Finish 20P-M"
Introduction
| * |
Mild Finish 20P-M is a skincare finishing agent/softener
developed to meet natural-oriented demand for textile
goods, mainly comprised of natural components and substances
considered safe for the skin and commonly used in cosmetics. |
| * |
The main component of Mild Finish 20P-M is highly-refined
squalane, which is chemically-stabilized squalene made
from shark liver oil. |
| * |
Squalane is an important base-material oil, widely
used in cosmetics, medicinal ointment, hemorrhoid or
other remedies for its chemical stability, biological
inertness, skin permeability, spreadability, affinity
and moisture-retaining properties, while squalene is
a familiar health food. |
| * |
Mild Finish 20P-M is a very safe emulsion mainly composed
of naturally-derived squalane with advantages mentioned
above, other natural ingredients and surfactants commonly
used in cosmetics. |
Description
| Appearance |
: |
Milky white emulsion |
| Main component |
: |
26 ± 1% |
| Ionicity |
: |
Nonionic |
| pH |
: |
6.5±1 (stock solution) |
| Viscosity |
: |
100mPa･s or less (25ﾟC) |
| Solubility |
: |
Dissolves readily in cold water |
Features
| * |
Imparts to any fiber material silky, soft hand, different
to the sleekness of silicone-based finishes. |
| * |
Produces effects gentle to the skin. |
| * |
Does not cause any hindrance to hydrophilic properties
or water absorbency of fiber. |
| * |
Does not cause shade alteration due to good resistance
to heat. |
| * |
I Allows simultaneous use with other chemicals due
to its nonionic disposition and good compatibility. |
| * |
Produces smoothness equivalent to that produced by
dimethyl silicone. |
Application
| * |
Believed suitable for use in garments, such as sportswear,
leisurewear, baby wear, general underwear and outerwear,
as well as in hygiene products such as disposable nappies. |
Packaging
Examples of application
| 1) |
Produces soft hand without tackiness in cellulose fiber,
such as cotton and rayon, wool, acrylics and polyester
through padding treatment. |
| Treatment: |
Padding → Drying
(70-100ﾟC) → Curing
(140-180ﾟC) (curing can be abbreviated)
A 2-3% solution is preferred as a padding bath with Mild Finish 20P-M,
while a 1-5% solution is usually used. |
| 2) |
Favorable hand can also be attained in hydrophilic
fiber such as cotton by the use of the dipping method. |
| Treatment: |
Dipping (40-60ﾟC) → Dehydration→ Drying
(70-100ﾟC) → Curing
(140-180ﾟC)
(curing can be abbreviated)
Liqour ratio = 1:20
The concentration used for a Mild Finish 20P-M dipping bath is 1-5%
o.w.f. |
| Remarks: |
Though little deterioration in dyeing fastness is
expected, verification by preliminary testing is necessary. |
Properties of wastewater
| Attribute (concentration) |
BOD (1g/L) |
COD (1g/L) |
| Measurement |
195mg/L |
206mg/L |
Directions for use
- Verify compatibility with other chemicals before use. Dilute
with cold or warm water before addition.
- Verify performance and other factors during treatment or
after use as required.
Handling instructions
- Ensure that the workplace is well ventilated and avoid
contact with the eyes and skin. Use protective clothing as
required. Wash hands and face thoroughly after use.
- In the event of direct contact with the eyes, wash the
eyes immediately under running water for 15 minutes or more,
and seek prompt medical attention.
- In the event of swallowing, spit out immediately (but do
not induce vomiting if unsuccessful), and seek prompt medical
attention.
- In the event of inhalation, remove immediately to fresh
air, rest and preserve body heat. Seek medical help if required.
- Use this product as soon as possible and avoid outside
storage. Store in a cool, dry place at a temperature between
5-35ﾟC away from direct sunlight in air-tight conditions.
- For further details, please refer to the Material Safety
Data Sheet.
| While the information presented here is based on data
from exhaustive in-company testing, it does not guarantee
results in practical use. The description above is subject
to change according to improvements in performance or
specifications. There is no guarantee that any patents
or legal rights are not infringed upon, with regard to
the specifications for this product. |
|
|